Видео

What was the reason you changed the resistor in the first place? No low speed? When you did the resistor test. Were you testing the resistor your took out of the new one you put in?

service and check engine are two different things. you say the light in the middle. that's the service light. just needs an oil change.

Duct tape a smaller diameter tube to the end of a wet/dry vacuum hose. Feed into ac drain and suction out.

Mines ain’t getting ground. What does that mean?

Richpin, I have a 1998 Saturn SW1. I doe not have a secondary pump in the location shown on this video.(Right below the wiper fluid reservoir). I have searched the internet until my fingers hurt. I do not even see that part for my year and model of Saturn. Do you know if my year and model even had a secondary air pump?

Hola , como quito el cedazo ?

I love all your videos but I am astonished that you didn't include any footage of installing the new head gasket!!!

Thanks , great video. Just what I was looking for.

Is it (Immobilizer) ?

Thank you - no wonder I couldn't see it on an N16 Pulsar

Thanks

Will welcome me to the club. Mines blew up today. 😂

Can that cluster be opened up to check for poor connections of the led backlighting or for cold solder joints? Mine has an intermittent backlight flicker or on off on both the speedo and odometer. Same for my cruise control light.

Best how to video for this car I've seen yet

"This little piece right here" at 1:39 made all the difference! Thanks!

My 10mm nuts on the heat riser snapped off on one side. What do I do now???

The big 15-16 is a solid state relay. It's like the points

I never want a yankee to make fun of my Southern accent EVER again.

Thanks bro. 💪🏽

Hey rich, I wanted to know the procedure to reset a Saturn SC airbag sensor, changed the airbags and checked the airbag fuse but the light is still on. Ive read that the airbag sensor needs to be reset as well with a BCM scanner, wanted to know if there was another way, as well as confirm if this was true. Please and thank you.

How much is the computer and can u install yourself or chevy have to do it

I think that was Peter griffin.

Removal of the transmission/motor assembly, put a 13 km wrench on the motor shaft nut, and turn it clockwise until the short arms of the transmission parallel of ram For easy removal of the motor/transmission, use a 13 mm wrench on the nut on the motor shaft and turn clockwise until the short arms of the transmission parallelogram are parallel to the midline of the car. Slips right out

I have an 06 grand Cherokee and my blower motor has different screw pattern and more and the plug is in a completely different location than this. Don't know why.

@2:03 Where longer bolts go and where shorter ones? I removed the Steering Pump with the Bracket for one project and forgot to mark where would be shorter and where longer bolts.

Excellent video. You showed us what to look for as the job progressed and how to address it. Other videos I've watched don't go into the detail you do on this repair. Kudos to on your attention to detail.

Great Info

What year is that montero?

Thank you, really helped me

Of course i see this the day after i bought my replacement HF jack that i purchased bc the previous jack stopped lifting after 10 years. Maybe ill try this for the heck of it and donate it to someone.

Hi,This is Astra from Roadanvi.We are a brand specializing in car stereos, infotainment systems, and related accessories.Because we know your email gets very many emails every day, but I don't want to lose the opportunity to work with you, so I tried to contact you here. I was wondering if you'd be interested in a new head unit for your Ford? Or if you have another car model, let me know, as long as we have a radio that fits your original car. We would be delighted if you could do a review video on your RUclips channel,lf you interested, hope you can reply and please send us your address to ship the package.

really helpful video even 9 years later, golf has refused to start sometimes when warm so hopefully a new crank sensor will solve it :) Thank you!

It worked. Thanks

You are a legend! thank you

ThankS👍👍

Thank you so much

Excellent!

Very informative video I appreciate your time you have learned me a lot especially about the differents in low side and high how to trouble shoot

Clear, concise and professional, as ALWAYS! NICE JOB 👏👏👏

Many thanks Rich! Superb demo!

Do you need to loosen the bolts on the frame to release pressure or smth on the DS after you replaced the DS Dog Bone Mount? In another film for the Dog Bone Mount on the PS it was done, but in this film (on the DS) - not. Thank you for the great film.

@4:50 Do you need to loosen those bolts on the DS after you replaced the DS Dog Bone Mount? Thank you for the great film.

Olive spoon

It's either the intake valve or the exhaust valve

generally if you have that kind of resistance the blower motor is working harder than it needs to be and is simply wearing out. When my blower locked up one day it took out the resistor pack with it

Don't work

Thanks!

I have a red warning light that looks like a radiator but my gauge doesn’t move or it overheats, any suggestions?

Better than the Haynes manual!

Valve